So you hooked up your entertainment sound system. you followed all the directions and spent countless hours on you tube trying to figure out whats going on If your not getting any sound from your speakers. It’s extremely unlikely everything has stopped working. So you just have to narrow it down and pin point where the problem is accruing. Try these things below before you go any further.
What Makes A Speaker Stop Working
Failures in tweeters, midrange and midbass speakers are caused by ELECTRICAL and/or MECHANICAL power handling issues. Most failures occur from ELECTRICAL failure caused by applying too much power to the speaker’s voice coil.
How Do I Know My Speakers Are Blown Out
If there is a lack of bass, treble, or mid-tones. If you’re not getting the booming sound of bass or vibration from the speakers.
The easiest way to find out what speakers are doing or not doing is to check them independently.
Nothing Turns ON
I know you might think this is a silly answer but happens more times then not. make sure everything is plugged in and not loose. A lot of time it’s a loose connection if this is the problem then that was an easy fix be happy.
If your not getting any sound from your speakers check to make sure you have the right settings set up. What I mean by that is going into your setting and make sure they are pointing in the right directions. Surround sound theater, 5.1, movie, music, etc. You can toggle through the buttons until you get sound. If that doesn’t work then you will have to do this check the back of your receiver to make sure all the wires are correctly installed.
For the most part it’s a connection problem. If you are still not getting anything it may be a bigger problem. That’s when you want to consult with your local pro to help fix the problem.
Your DVD Player Will Not Work
So what’s going on with your DVD player and why it’s not working. It’s tough for me to pin point the issue without knowing the problem. But again here are some common problems you might have with your DVD player.
How To Fix Your DVD Tray That Won’t Open
DVD Player Not Working With Your TV
We all know how frustrating it can be when you’re looking forward to settling down to a good film, but your DVD player doesn’t seem to be talking to your TV – it’s even more frustrating when you can’t figure out why. So here are a few things to check.
- Is There Power To Your Device? Try switching it on using the power button on the device, rather than the remote. If it turns on, it probably means your remote is either faulty or the batteries need changing.
- If your TV or DVD player still doesn’t switch on, it could be a fuse in the plug.
- If you’ve changed the plug fuse and it still won’t switch on, it means there’s a more serious fault, and it’ll need to be looked at my an engineer.
Is There a Problem With Your Connection
Whether you’re using an HDMI, RCA, or composite video cables, the first thing to check is that it’s securely connected at both ends. If the picture flickers as you move the cable in its socket, it likely means that the socket is faulty. Most TV’s have a few HDMI sockets, so try plugging the cable into a spare one.
Sometimes the cable itself can develop a fault and stop working, so just switching cables can be a cheap and easy fix.
You can pick up a new HDMI cable here.
Is Your DVD Disc Damaged?
Marks and scratches on DVDs or Blu-ray discs can seriously affect how well they work. Check the reflective side of the disc for any marks – if the disc is badly damaged, it’s probably time to replace it. But if it’s just dirt or greasy marks, you could try giving it a gentle clean with a soft, non-abrasive cloth.
Does Your Player Lens Need Cleaning?
If you’ve had the DVD or Blu-ray player for a while, it might have accumulated some dust on the lens. Don’t worry though, you don’t need to start taking it apart to clean it. Laser lens cleaning discs make this a really easy fix, you just pop the disc into the player and it’ll clean the lens within a few seconds.
If you think this might be the problem, you can pick up a laser lens cleaning disc here.
So Is Your TV Causing The Problem?
If this is the case and it will be without even thinking of it. Just make sure you’ve chosen the correct source on the TV. The source button on your remote usually looks like a square with an arrow pointing at it – press this to switch between sources. If your DVD player is connected by an HDMI cable, you might need to switch between them to find the right one. Just make sure the DVD player is switched on first. Otherwise, the TV won’t find it.
Having Trouble Streaming Movies?
Are you having trouble streaming your movies? Most of the time it will be buffering problems. When buffering occurs when watching movie it’s because the internet is bogged down.
Slow internet speeds. You might want to consider upgrading your internet speeds as this is the most common reason. If you do not want to do that continue reading.
Shutting down your devices. Stop all other active downloads on your computer, phone or ipad. Anything that might be slowing down your Wi-Fi.
Pausing your movie. This will help with the streaming to catch up with the movie. This will work temporarily but will continue to do this throughout the movie. It’s frustrating and time consuming just to get through a movie. Doesn’t make it an enjoyable experience. I don’t know about you but I don’t have the Patience for that.
Wait until the services for the content provider are less busy. You can wait until there are slower hours of people on the internet so speeds are better. There are peek hours when the world is just on the internet. You can wait for that to slow down and watch your movie later in the night when people are going to bed.
That’s up to you, but when I want to watch a movie with my family I’m not going to wait for the internet to slow down. If you are really having these problems consider upgrading. believe me it’s worth it.
To Sum It Up
In most cases of common home theater problems it’s going to be a connection problem, settings not being set up correctly, or just a slow internet. So your biggest problem is just to narrow it down. Once you do that the problem is pretty easy to fix.
If we can be any assistance, please leave a comment and we will be sure to get back to you with a solution.